Forum and Costume Controls

   FAQFAQ  SearchSearch  MemberlistMemberlist   UsergroupsUsergroups  medals.php?sid=bb15fe4c7e1991ae06e2e820536ada1bMedals   RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in

       
REMINDER: Do not change your e-mail address yourself. Please read this first for why.

[Standard Revision] Battle of Endor Leia
Goto page 1, 2  Next
 
Post new topic   This topic is locked: you cannot edit posts or make replies.    Rebel Legion Forum Index -> Costume and Prop Making -> Royalty/Senatorial -> RLGS Archive
View previous topic :: View next topic  
Author Message
SongofAmazon (Jenna)
Detachment CO
Detachment CO


Joined: 09 Aug 2008
Posts: 2633
Location: Silver Spring, MD
Medals: None

PostPosted: Fri Oct 06, 2017 1:39 am    Post subject: [Standard Revision] Battle of Endor Leia Reply with quote

Battle of Endor (Commando and Briefing Room) Leia Standards


Endor Briefing Room Version:
Shirt, Pants, Boots, Wrist Communicator, Vest, Rank Insignia, Belt, Belt Buckle, Front Pouch, Back 2-3 pouches, holster, with optional blaster and Hair style with optional leather "x" detail

Endor Commando Version:
Shirt, Pants, Poncho, Boots, Wrist Communicator, Belt, Belt Buckle, Front Pouch, Back 2-3 pouches, holster, with optional blaster, Hair style with optional leather "x" detail, optional vest and optional helmet.

(Each version must be approved seperately)


Both Versions:

Shirt
1. Tan or beige short sleeved shirt, with the following elements included:
a. sleeves should reach almost to the elbow with a wide approximately 3 inch/7.6 cm cuff folded up
b. each sleeve features a vented pocket (roughly 4 inch by 5 inch/10 cm by 12.7 cm) and flap partially sewn to the outside of each sleeve. The pocket should lay over the cuff.
c. the collar on the shirt should be loose fitting, and have a pointed shape
d. the shirt should close right over left and lay open to the upper breastbone with no visible snaps, zippers or other closures.

2. Cool pale blue/grey-blue twill pants, tailored with a natural waist height. A solid burnished yellow or gold non-shiny stripe about 1 inch/2.5 cm wide on each side seam. The pants should fit loosely enough to billow slightly at the top of the boot.

3. Low-heeled black leather or leather-like, non-shiny riding boots. Boots must be at least calf-high and loose-fitting; no zippers unless covered.

4. Black and silver watch-like communication device on left wrist with a black strap. Painted and weathered to match screen references.

5. Olive green 2” wide twill belt with the following details:
a. a black metal slide in front approximately 1.5-2 inch/3.8-5 cm in width and 3-3.5 inches/7.6-8.8 cm in height
b. one black non-shiny leather, suede or leather-like pouch (the fuzzy side of pig skin recommended) on the left front. Pouch should have a boxy shape with curved lower edges and feature a thin (1.5 inch/3.8 cm strap to hold the top in place.
c. 2-3 black non-shiny leather, suede or leather-like pouches (the fuzzy side of pig skin recommended) in the back with no visible snaps.
d. A black leather or vinyl holster.

6. Two braids wrapped around head with a densely braided figure eight-style bun in back. Optional thin tan/beige suede or leather like chording in a wide "x" pattern over the top of each front braid.Naturally-occurring hair color only (brown preferred); no bangs. If a wig or hairpieces are used, they should be of high-quality and appear like real hair.

Endor Briefing Version Only:
1. Medium gray vest with cap sleeves. The vest should include the following details:
a. gathering at the waist with a 1.5-2 inch/3.8-5 cm band featuring top stitching around the edges.
b. top stitching approximately 1-1.5 inches/2.5-3.8 cm from the outside edge on both the right and left sides, and 5 decorative topstitches about 1 inch/2.5 cm apart on the right-front (not including the edge top-stitching) and 8 decorative topstitches about 1 inch/2.5 cm apart along the right-back yoke.
c. one knife pleat folded upward and top-stitched approximately 0.5 inches/1.25 cm on the front right and left sides of the vest. This should angle down lower closer to the side seams of the vest.
d. a front yoke starting roughly 1 inch/2.5 cm from the top of the knife pleat and angling up toward the sleeve opening
e. a back yoke angling up slightly from the back center point.
f. top stitching around the sleeve seam, front yoke and back yoke is preferred but not required.

2.Rank insignia on the front right breast painted and weathered to match screen references.


Endor Commando Version Only:
1. Poncho with hood and ovular donut-shaped face opening featuring the following:
a. Poncho has a blotchy camouflage pattern, no streaks or lines, and is colored to match screen references with all of the following colors included: brown, light green, dark green and cream-white
a. poncho should hit at upper thigh level in front and at knee level in back
b. poncho should hit at or just past elbow level when viewed from the side
c. poncho has 2 slit openings in the front at the natural body line to allow the belt to pass through the front of the poncho, there should be at least 8 inches/20 cm of fabric on each outside edge of the slit.
d. poncho does not have shoulder seams and includes a seam approximately 6inches/15 cm from each edge (optional top stitching on this seam)
e. poncho features a hood that can cover the helmet when worn, hood should hit shoulder-blade-mid back level in back and should have 2-4 inches/5-10 cm of fabric in front
d. ovular donut shape connected to the hood that frames the face, approximately 3 inches/7.6 cm wide. Lining preferred on donut shape
e. poncho is self-lined and inside of poncho is colored to match screen references similar to the outside of poncho


Optional Items:
1. X-30 Lancer Target Blast pistol.
2. (Commando Only) Rebel commando helmet featuring inner and outer elements:
a. a tan colored under-helmet based on a WWII era light weight AN-H--15 type flying cap with a custom ribbed top and visor. Ear flaps with black round shapes covering each ear. Mesh should cover the openings in each black round ear flap
b. a hard olive colored outer helmet featuring screen accurate black striping in back, 1 red and yellow insignia on front right side, painted, and weathered to match screen references including 3 dents.
3.(Commando Only)Grey Vest and Rank Insignia (see standards under Endor Briefing Room Version)
4. Various levels of screen accurate weathering


Rebel Briefing Leia Reference Gallery: http://www.senate.rebellegion.com/?portfolio=princess-leia-organa-rebel-briefing-uniform
Endor Commando Leia Reference Gallery: http://www.senate.rebellegion.com/?portfolio=princess-leia-organa-endor-commando-poncho
_________________


In planning and progress:
Riyo Chuchi, Queen Apailana, Nomi Sunrider, Havoc Trooper, Amilyn Holdo

Galactic Senate DCO | RLGS FaceBook | RLGS Web Site
Back to top
View user's profile Send private message Visit poster's website
Obi Anne (Johanna Nybelius)
Active Legion Member


Joined: 23 Nov 2002
Posts: 1652

Medals: 2 (View more...)
Rebel Legion Supporter (Amount: 1)

PostPosted: Fri Oct 06, 2017 5:56 am    Post subject: Reply with quote

I only have a question about the boots, and it's more about consistency over the different standards. In this standards it says outrigt "no zippers, unless covered". I have been approved with other costumes, for example General Leia, with a zipper on the inside of the boot.

I think that this is an issue, that should probably be discussed among LCJs and detachment leaders, but I think it would be good if here was a general RL policy on what is and isn't allowed regarding zippers on boots.
Back to top
View user's profile Send private message
Lora Skywalker ()
Detachment XO
Detachment XO


Joined: 24 Jul 2008
Posts: 6353

Medals: None

PostPosted: Sat Oct 07, 2017 8:46 pm    Post subject: Reply with quote

It probably would be. But some costumes have very specific boot styles while others don't.

How would other feels about a color neutral zipper (aka black) that wasn't covered?
_________________
DXO of Royalty & Senatorial detachment

Detachment website: http://www.senate.rebellegion.com/
Back to top
View user's profile Send private message Visit poster's website
Ritin Kornas ()
Active Legion Member


Joined: 09 Jun 2009
Posts: 612
Location: Switzerland
Medals: None

PostPosted: Sat Oct 07, 2017 10:49 pm    Post subject: Reply with quote

Lora Skywalker wrote:
It probably would be. But some costumes have very specific boot styles while others don't.

How would other feels about a color neutral zipper (aka black) that wasn't covered?

I'm always in favor of allowing liberties on things you can't see Smile So if it's inside of the foot, don't see any objection personally Smile
_________________
CO Rebel Legion Helvetica Base (serving Switzerland)
Member of the RL Galactic Senate Council
Back to top
View user's profile Send private message
Blue (Beth)
Legion Costume Judge
Legion Costume Judge


Joined: 26 Apr 2005
Posts: 2223
Location: Wisconsin, USA
Medals: None

PostPosted: Mon Oct 09, 2017 3:12 pm    Post subject: Reply with quote

It would make finding boots easier. It look me a long time to find a boot that was wide enough for my calf with no zippers.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Daughter of Alderaan (Joy Lochelt)
Active Legion Member


Joined: 21 Apr 2015
Posts: 293

Medals: None

PostPosted: Wed Oct 11, 2017 3:53 am    Post subject: Re: [Standard Revision] Battle of Endor Leia Reply with quote

edited boots per Beth

Battle of Endor (Commando and Briefing Room) Leia Standards


Endor Briefing Room Version:
Shirt, Pants, Boots, Wrist Communicator, Vest, Rank Insignia, Belt, Belt Buckle, Front Pouch, Back 2-3 pouches, holster, with optional blaster and Hair style with optional leather "x" detail

Endor Commando Version:
Shirt, Pants, Poncho, Boots, Wrist Communicator, Belt, Belt Buckle, Front Pouch, Back 2-3 pouches, holster, with optional blaster, Hair style with optional leather "x" detail, optional vest and optional helmet.

(Each version must be approved seperately)


Both Versions:

Shirt
1. Tan or beige short sleeved shirt, with the following elements included:
a. sleeves should reach almost to the elbow with a wide approximately 3 inch/7.6 cm cuff folded up
b. each sleeve features a vented pocket (roughly 4 inch by 5 inch/10 cm by 12.7 cm) and flap partially sewn to the outside of each sleeve. The pocket should lay over the cuff.
c. the collar on the shirt should be loose fitting, and have a pointed shape
d. the shirt should close right over left and lay open to the upper breastbone with no visible snaps, zippers or other closures.

2. Cool pale blue/grey-blue twill pants, tailored with a natural waist height. A solid burnished yellow or gold non-shiny stripe about 1 inch/2.5 cm wide on each side seam. The pants should fit loosely enough to billow slightly at the top of the boot.

3. Low-heeled, black leather or leather-like, non-shiny boots. Boots must be over calf and loose-fitting; no zippers unless covered or a black zipper located on inside of leg. No buckles or straps.

4. Black and silver watch-like communication device on left wrist with a black strap. Painted and weathered to match screen references.

5. Olive green 2” wide twill belt with the following details:
a. a black metal slide in front approximately 1.5-2 inch/3.8-5 cm in width and 3-3.5 inches/7.6-8.8 cm in height
b. one black non-shiny leather, suede or leather-like pouch (the fuzzy side of pig skin recommended) on the left front. Pouch should have a boxy shape with curved lower edges and feature a thin (1.5 inch/3.8 cm strap to hold the top in place.
c. 2-3 black non-shiny leather, suede or leather-like pouches (the fuzzy side of pig skin recommended) in the back with no visible snaps.
d. A black leather or vinyl holster.

6. Two braids wrapped around head with a densely braided figure eight-style bun in back. Optional thin tan/beige suede or leather like chording in a wide "x" pattern over the top of each front braid.Naturally-occurring hair color only (brown preferred); no bangs. If a wig or hairpieces are used, they should be of high-quality and appear like real hair.

Endor Briefing Version Only:
1. Medium gray vest with cap sleeves. The vest should include the following details:
a. gathering at the waist with a 1.5-2 inch/3.8-5 cm band featuring top stitching around the edges.
b. top stitching approximately 1-1.5 inches/2.5-3.8 cm from the outside edge on both the right and left sides, and 5 decorative topstitches about 1 inch/2.5 cm apart on the right-front (not including the edge top-stitching) and 8 decorative topstitches about 1 inch/2.5 cm apart along the right-back yoke.
c. one knife pleat folded upward and top-stitched approximately 0.5 inches/1.25 cm on the front right and left sides of the vest. This should angle down lower closer to the side seams of the vest.
d. a front yoke starting roughly 1 inch/2.5 cm from the top of the knife pleat and angling up toward the sleeve opening
e. a back yoke angling up slightly from the back center point.
f. top stitching around the sleeve seam, front yoke and back yoke is preferred but not required.

2.Rank insignia on the front right breast painted and weathered to match screen references.


Endor Commando Version Only:
1. Poncho with hood and ovular donut-shaped face opening featuring the following:
a. Poncho has a blotchy camouflage pattern, no streaks or lines, and is colored to match screen references with all of the following colors included: brown, light green, dark green and cream-white
a. poncho should hit at upper thigh level in front and at knee level in back
b. poncho should hit at or just past elbow level when viewed from the side
c. poncho has 2 slit openings in the front at the natural body line to allow the belt to pass through the front of the poncho, there should be at least 8 inches/20 cm of fabric on each outside edge of the slit.
d. poncho does not have shoulder seams and includes a seam approximately 6inches/15 cm from each edge (optional top stitching on this seam)
e. poncho features a hood that can cover the helmet when worn, hood should hit shoulder-blade-mid back level in back and should have 2-4 inches/5-10 cm of fabric in front
d. ovular donut shape connected to the hood that frames the face, approximately 3 inches/7.6 cm wide. Lining preferred on donut shape
e. poncho is self-lined and inside of poncho is colored to match screen references similar to the outside of poncho


Optional Items:
1. X-30 Lancer Target Blast pistol.
2. (Commando Only) Rebel commando helmet featuring inner and outer elements:
a. a tan colored under-helmet based on a WWII era light weight AN-H--15 type flying cap with a custom ribbed top and visor. Ear flaps with black round shapes covering each ear. Mesh should cover the openings in each black round ear flap
b. a hard olive colored outer helmet featuring screen accurate black striping in back, 1 red and yellow insignia on front right side, painted, and weathered to match screen references including 3 dents.
3.(Commando Only)Grey Vest and Rank Insignia (see standards under Endor Briefing Room Version)
4. Various levels of screen accurate weathering


Rebel Briefing Leia Reference Gallery: http://www.senate.rebellegion.com/?portfolio=princess-leia-organa-rebel-briefing-uniform
Endor Commando Leia Reference Gallery: http://www.senate.rebellegion.com/?portfolio=princess-leia-organa-endor-commando-poncho
_________________

Photos by Robbins Studios

In Progress:Padme Loyalist Gown, Leia Raddus Bridge
Back to top
View user's profile Send private message
Ritin Kornas ()
Active Legion Member


Joined: 09 Jun 2009
Posts: 612
Location: Switzerland
Medals: None

PostPosted: Fri Oct 20, 2017 8:19 am    Post subject: Reply with quote

Following LeiaAurora question about the donut in her build thread (http://www.forum.rebellegion.com/forum/viewtopic.php?t=88209&start=30), should we be more specific on the helmet ?
Specially as the endor commando standard his absolutely not precise (http://newsite.rebellegion.com/endor-commando-rebel-soldier-trooper/)
There is problem in the current standard as the donut appear at same time mandatory and optional for the commando version.
In red removal, blue addition, green notes to be removed after.




____________________________________________________




Battle of Endor (Commando and Briefing Room) Leia Standards


Endor Briefing Room Version:
Shirt, Pants, Boots, Wrist Communicator, Vest, Rank Insignia, Belt, Belt Buckle, Front Pouch, Back 2-3 pouches, holster, with optional blaster and Hair style with optional leather "x" detail

Endor Commando Version:
Shirt, Pants, Poncho, Boots, Wrist Communicator, Belt, Belt Buckle, Front Pouch, Back 2-3 pouches, holster, with optional blaster, Hair style with optional leather "x" detail, optional vest and optional helmet.

(Each version must be approved seperately)


Both Versions:

Shirt
1. Tan or beige short sleeved shirt, with the following elements included:
a. sleeves should reach almost to the elbow with a wide approximately 3 inch/7.6 cm cuff folded up
b. each sleeve features a vented pocket (roughly 4 inch by 5 inch/10 cm by 12.7 cm) and flap partially sewn to the outside of each sleeve. The pocket should lay over the cuff.
c. the collar on the shirt should be loose fitting, and have a pointed shape
d. the shirt should close right over left and lay open to the upper breastbone with no visible snaps, zippers or other closures.

2. Cool pale blue/grey-blue twill pants, tailored with a natural waist height. A solid burnished yellow or gold non-shiny stripe about 1 inch/2.5 cm wide on each side seam. The pants should fit loosely enough to billow slightly at the top of the boot.

3. Low-heeled, black leather or leather-like, non-shiny boots. Boots must be over calf and loose-fitting; no zippers unless covered or a black zipper located on inside of leg. No buckles or straps.

4. Black and silver watch-like communication device on left wrist with a black strap. Painted and weathered to match screen references.

5. Olive green 2” wide twill belt with the following details:
a. a black metal slide in front approximately 1.5-2 inch/3.8-5 cm in width and 3-3.5 inches/7.6-8.8 cm in height
b. one black non-shiny leather, suede or leather-like pouch (the fuzzy side of pig skin recommended) on the left front. Pouch should have a boxy shape with curved lower edges and feature a thin (1.5 inch/3.8 cm strap to hold the top in place.
c. 2-3 black non-shiny leather, suede or leather-like pouches (the fuzzy side of pig skin recommended) in the back with no visible snaps.
d. A black leather or vinyl holster.

6. Two braids wrapped around head with a densely braided figure eight-style bun in back. Optional thin tan/beige suede or leather like chording in a wide "x" pattern over the top of each front braid.Naturally-occurring hair color only (brown preferred); no bangs. If a wig or hairpieces are used, they should be of high-quality and appear like real hair.

Endor Briefing Version Only:
1. Medium gray vest with cap sleeves. The vest should include the following details:
a. gathering at the waist with a 1.5-2 inch/3.8-5 cm band featuring top stitching around the edges.
b. top stitching approximately 1-1.5 inches/2.5-3.8 cm from the outside edge on both the right and left sides, and 5 decorative topstitches about 1 inch/2.5 cm apart on the right-front (not including the edge top-stitching) and 8 decorative topstitches about 1 inch/2.5 cm apart along the right-back yoke.
c. one knife pleat folded upward and top-stitched approximately 0.5 inches/1.25 cm on the front right and left sides of the vest. This should angle down lower closer to the side seams of the vest.
d. a front yoke starting roughly 1 inch/2.5 cm from the top of the knife pleat and angling up toward the sleeve opening
e. a back yoke angling up slightly from the back center point.
f. top stitching around the sleeve seam, front yoke and back yoke is preferred but not required.

2.Rank insignia on the front right breast painted and weathered to match screen references.


Endor Commando Version Only:
1. Poncho with hood and ovular donut-shaped face opening featuring the following:
a. Poncho has a blotchy camouflage pattern, no streaks or lines, and is colored to match screen references with all of the following colors included: brown, light green, dark green and cream-white
a. poncho should hit at upper thigh level in front and at knee level in back
b. poncho should hit at or just past elbow level when viewed from the side
c. poncho has 2 slit openings in the front at the natural body line to allow the belt to pass through the front of the poncho, there should be at least 8 inches/20 cm of fabric on each outside edge of the slit.
d. poncho does not have shoulder seams and includes a seam approximately 6inches/15 cm from each edge (optional top stitching on this seam)
e. poncho features a hood that can cover the helmet when worn, hood should hit shoulder-blade-mid back level in back and should have 2-4 inches/5-10 cm of fabric in front
Or I don't see what is the ovular donut shape here if not the hard shell of helmet
d. ovular donut shape connected to the hood that frames the face, approximately 3 inches/7.6 cm wide. Lining preferred on donut shape
e.
d. poncho is self-lined and inside of poncho is colored to match screen references similar to the outside of poncho


Optional Items:
1. X-30 Lancer Target Blast pistol.
2. (Commando Only) Rebel commando helmet featuring inner and outer elements:
a. a tan colored under-helmet based on a WWII era light weight AN-H--15 type flying cap with a custom ribbed top and visor. Ear flaps with black round shapes covering each ear. Mesh should cover the openings in each black round ear flap
b. a hard olive colored outer helmet featuring screen accurate details, inluding 8 (preferred) or 9 black striping in back, 1 red and yellow insignia on front right side, painted, and weathered to match screen references including 3 dents. Top opening should be close to the cloth helmet and should not leave a big gap. Black striping is preferred to be indented and not painted only.
See here at 24 seconds for top view of the helmet http://www.starwars.com/video/leia-meets-wicket.
You can see here at 1:48 that there are 8 strips. But in the Battlefront game you have 9 on her helmet. https://youtu.be/6uEXykAHRJ0?t=1m48s
Regarding the facts stripes are indented and not painted, I put it that way as there is not strong certitude from reference images on that point. Even toys doesn't help here as some as just paint and some have indented them like sideshow figures. However, if you look closely in some shots of speeder bike chase, the paint is not chipped on the stipes like the olive surrounding, suggesting it is indented in the helmet shape. Also, most of the helmets I know are indented.

3.(Commando Only)Grey Vest and Rank Insignia (see standards under Endor Briefing Room Version)
4. Various levels of screen accurate weathering


Rebel Briefing Leia Reference Gallery: http://www.senate.rebellegion.com/?portfolio=princess-leia-organa-rebel-briefing-uniform
Endor Commando Leia Reference Gallery: http://www.senate.rebellegion.com/?portfolio=princess-leia-organa-endor-commando-poncho


_________________
CO Rebel Legion Helvetica Base (serving Switzerland)
Member of the RL Galactic Senate Council
Back to top
View user's profile Send private message
Leia (Vera Campbell)
Active Legion Member


Joined: 07 Jan 2003
Posts: 1342

Medals: 1 (View more...)
Gold Star (Amount: 1)

PostPosted: Thu Nov 02, 2017 1:02 am    Post subject: Reply with quote

But the poncho hood DOES have an oval opening to it, not just a regular old hood? I think this needs to stay in there.



I also think the belt shouldn't be listed as "Olive", that's a yellow color and quite subjective. It's a deep forest green.
_________________

Costumer of the Year - 2010
Current Build Threads: Meadow Gown: http://www.forum.rebellegion.com/forum/viewtopic.php?t=100662
Ceremonial Leia: http://www.forum.rebellegion.com/forum/viewtopic.php?p=986837#986837
Back to top
View user's profile Send private message Visit poster's website
Ritin Kornas ()
Active Legion Member


Joined: 09 Jun 2009
Posts: 612
Location: Switzerland
Medals: None

PostPosted: Thu Nov 02, 2017 8:26 pm    Post subject: Reply with quote

Leia wrote:
But the poncho hood DOES have an oval opening to it, not just a regular old hood? I think this needs to stay in there.



I also think the belt shouldn't be listed as "Olive", that's a yellow color and quite subjective. It's a deep forest green.


Well then if it's an opening it's still not something that is connecting to the hood, it's the shape of the hood. So I still think the way it is said is very weird and something need to be changed there Wink

Regarding the belt. Maybe simply then "Olive or deep forest green 2" twill belt [...]" ??
_________________
CO Rebel Legion Helvetica Base (serving Switzerland)
Member of the RL Galactic Senate Council
Back to top
View user's profile Send private message
SongofAmazon (Jenna)
Detachment CO
Detachment CO


Joined: 09 Aug 2008
Posts: 2633
Location: Silver Spring, MD
Medals: None

PostPosted: Fri Nov 03, 2017 1:40 am    Post subject: Reply with quote

How about 'drab' instead of olive? That covers the military green color that they may have been going for.

I also tweaked language about length that uses "hit," which could be confusing in a second language.

Quote:
Battle of Endor (Commando and Briefing Room) Leia Standards


Endor Briefing Room Version:
Shirt, Pants, Boots, Wrist Communicator, Vest, Rank Insignia, Belt, Belt Buckle, Front Pouch, Back 2-3 pouches, holster, with optional blaster and Hair style with optional leather "x" detail

Endor Commando Version:
Shirt, Pants, Poncho, Boots, Wrist Communicator, Belt, Belt Buckle, Front Pouch, Back 2-3 pouches, holster, with optional blaster, Hair style with optional leather "x" detail, optional vest and optional helmet.

(Each version must be approved seperately)


Both Versions:

Shirt
1. Tan or beige short sleeved shirt, with the following elements included:
a. sleeves should reach almost to the elbow with a wide approximately 3 inch/7.6 cm cuff folded up
b. each sleeve features a vented pocket (roughly 4 inch by 5 inch/10 cm by 12.7 cm) and flap partially sewn to the outside of each sleeve. The pocket should lay over the cuff.
c. the collar on the shirt should be loose fitting, and have a pointed shape
d. the shirt should close right over left and lay open to the upper breastbone with no visible snaps, zippers or other closures.

2. Cool pale blue/grey-blue twill pants, tailored with a natural waist height. A solid burnished yellow or gold non-shiny stripe about 1 inch/2.5 cm wide on each side seam. The pants should fit loosely enough to billow slightly at the top of the boot.

3. Low-heeled, black leather or leather-like, non-shiny boots. Boots must be over calf and loose-fitting; no zippers unless covered or a black zipper located on inside of leg. No buckles or straps.

4. Black and silver watch-like communication device on left wrist with a black strap. Painted and weathered to match screen references.

5. Forest or drab green 2” wide twill belt with the following details:
a. a black metal slide in front approximately 1.5-2 inch/3.8-5 cm in width and 3-3.5 inches/7.6-8.8 cm in height
b. one black non-shiny leather, suede or leather-like pouch (the fuzzy side of pig skin recommended) on the left front. Pouch should have a boxy shape with curved lower edges and feature a thin (1.5 inch/3.8 cm strap to hold the top in place.
c. 2-3 black non-shiny leather, suede or leather-like pouches (the fuzzy side of pig skin recommended) in the back with no visible snaps.
d. A black leather or vinyl holster.

6. Two braids wrapped around head with a densely braided figure eight-style bun in back. Optional thin tan/beige suede or leather like chording in a wide "x" pattern over the top of each front braid.Naturally-occurring hair color only (brown preferred); no bangs. If a wig or hairpieces are used, they should be of high-quality and appear like real hair.

Endor Briefing Version Only:
1. Medium gray vest with cap sleeves. The vest should include the following details:
a. gathering at the waist with a 1.5-2 inch/3.8-5 cm band featuring top stitching around the edges.
b. top stitching approximately 1-1.5 inches/2.5-3.8 cm from the outside edge on both the right and left sides, and 5 decorative topstitches about 1 inch/2.5 cm apart on the right-front (not including the edge top-stitching) and 8 decorative topstitches about 1 inch/2.5 cm apart along the right-back yoke.
c. one knife pleat folded upward and top-stitched approximately 0.5 inches/1.25 cm on the front right and left sides of the vest. This should angle down lower closer to the side seams of the vest.
d. a front yoke starting roughly 1 inch/2.5 cm from the top of the knife pleat and angling up toward the sleeve opening
e. a back yoke angling up slightly from the back center point.
f. top stitching around the sleeve seam, front yoke and back yoke is preferred but not required.

2.Rank insignia on the front right breast painted and weathered to match screen references.


Endor Commando Version Only:
1. Hooded poncho featuring the following:
a. Poncho has a blotchy camouflage pattern, no streaks or lines, and is colored to match screen references with all of the following colors included: brown, light green, dark green and cream-white
a. poncho should be upper thigh length in front and at knee level in back
b. poncho should as long as or just past elbow level when viewed from the side
c. poncho has 2 slit openings in the front at the natural body line to allow the belt to pass through the front of the poncho, there should be at least 8 inches/20 cm of fabric on each outside edge of the slit.
d. poncho does not have shoulder seams and includes a seam approximately 6 inches/15 cm from each edge (optional top stitching on this seam)
e. poncho features a hood that can cover the helmet when worn, hood should hang down to shoulder-blade/mid back level in back and should have 2-4 inches/5-10 cm of fabric in front. Hood should have oval-shaped opening for face.
f. poncho is self-lined and inside of poncho is colored to match screen references similar to the outside of poncho


Optional Items:
1. X-30 Lancer Target Blast pistol.
2. (Commando Only) Rebel commando helmet featuring inner and outer elements:
a. a tan colored under-helmet based on a WWII era light weight AN-H--15 type flying cap with a custom ribbed top and visor. Ear flaps with black round shapes covering each ear. Mesh should cover the openings in each black round ear flap
b. a hard olive colored outer helmet featuring screen accurate details, inluding 8 (preferred) or 9 black striping in back, 1 red and yellow insignia on front right side, painted, and weathered to match screen references including 3 dents. Top opening should be close to the cloth helmet and should not leave a big gap. Black striping is preferred to be indented and not painted only.
See here at 24 seconds for top view of the helmet http://www.starwars.com/video/leia-meets-wicket.
You can see here at 1:48 that there are 8 strips. But in the Battlefront game you have 9 on her helmet. https://youtu.be/6uEXykAHRJ0?t=1m48s
Regarding the facts stripes are indented and not painted, I put it that way as there is not strong certitude from reference images on that point. Even toys doesn't help here as some as just paint and some have indented them like sideshow figures. However, if you look closely in some shots of speeder bike chase, the paint is not chipped on the stipes like the olive surrounding, suggesting it is indented in the helmet shape. Also, most of the helmets I know are indented.

3.(Commando Only)Grey Vest and Rank Insignia (see standards under Endor Briefing Room Version)
4. Various levels of screen accurate weathering


Rebel Briefing Leia Reference Gallery: http://www.senate.rebellegion.com/?portfolio=princess-leia-organa-rebel-briefing-uniform
Endor Commando Leia Reference Gallery: http://www.senate.rebellegion.com/?portfolio=princess-leia-organa-endor-commando-poncho


_________________


In planning and progress:
Riyo Chuchi, Queen Apailana, Nomi Sunrider, Havoc Trooper, Amilyn Holdo

Galactic Senate DCO | RLGS FaceBook | RLGS Web Site
Back to top
View user's profile Send private message Visit poster's website
Ritin Kornas ()
Active Legion Member


Joined: 09 Jun 2009
Posts: 612
Location: Switzerland
Medals: None

PostPosted: Fri Nov 03, 2017 1:45 pm    Post subject: Reply with quote

Looks good to me like that Smile

Except you should remove my green comment form it in, regarding the soft and hard helmet with no gap in between ^^
_________________
CO Rebel Legion Helvetica Base (serving Switzerland)
Member of the RL Galactic Senate Council
Back to top
View user's profile Send private message
Leia (Vera Campbell)
Active Legion Member


Joined: 07 Jan 2003
Posts: 1342

Medals: 1 (View more...)
Gold Star (Amount: 1)

PostPosted: Fri Nov 03, 2017 8:11 pm    Post subject: Reply with quote

Ritin Kornas wrote:
Well then if it's an opening it's still not something that is connecting to the hood, it's the shape of the hood. So I still think the way it is said is very weird and something need to be changed there Wink

Regarding the belt. Maybe simply then "Olive or deep forest green 2" twill belt [...]" ??


Yes, actually, it IS attached to the hood, I've done extensive research on it. You can see it in the Endor Trooper Q&A thread, and if you study the shape of the hood, you can clearly see the attachment seam for the Oval Shaped opening.



Here is how the hood is shaped. The hood should NOT be open like a Jedi robe hood. When her hood is down, you can see the ring/oval shape sitting on the top, and the rest of the hood is what's bunched up underneath.

Regarding the color, olive drab is a lighter, military color, Leia's belt is extremely dark.



Olive/olive drab usually looks like this. Before I made a case for the green years ago, it used to say the belt was black.


_________________

Costumer of the Year - 2010
Current Build Threads: Meadow Gown: http://www.forum.rebellegion.com/forum/viewtopic.php?t=100662
Ceremonial Leia: http://www.forum.rebellegion.com/forum/viewtopic.php?p=986837#986837
Back to top
View user's profile Send private message Visit poster's website
Ritin Kornas ()
Active Legion Member


Joined: 09 Jun 2009
Posts: 612
Location: Switzerland
Medals: None

PostPosted: Fri Nov 03, 2017 11:07 pm    Post subject: Reply with quote

Hoooooo I get what you mean now. And I persist it's not connected to the hood but it IS the hood ^^ But I see the point now, wasn't clear to me it was this before!


Ok, maybe can I propose the following then. What do you think of... ?
Quote:

Endor Commando Version Only:
1. Hooded poncho featuring the following:
a. Poncho has a blotchy camouflage pattern, no streaks or lines, and is colored to match screen references with all of the following colors included: brown, light green, dark green and cream-white
a. poncho should be upper thigh length in front and at knee level in back
b. poncho should as long as or just past elbow level when viewed from the side
c. poncho has 2 slit openings in the front at the natural body line to allow the belt to pass through the front of the poncho, there should be at least 8 inches/20 cm of fabric on each outside edge of the slit.
d. poncho does not have shoulder seams and includes a seam approximately 6 inches/15 cm from each edge (optional top stitching on this seam)
e. poncho features a hood that can cover the helmet when worn, hood should hang down to shoulder-blade/mid back level in back and should have 2-4 inches/5-10 cm of fabric in front. When hood is folded, the fabric of the hood should make a donut shape around the neck. Hood should have oval-shaped opening for face.
f. poncho is self-lined and inside of poncho is colored to match screen references similar to the outside of poncho

_________________
CO Rebel Legion Helvetica Base (serving Switzerland)
Member of the RL Galactic Senate Council
Back to top
View user's profile Send private message
Leia (Vera Campbell)
Active Legion Member


Joined: 07 Jan 2003
Posts: 1342

Medals: 1 (View more...)
Gold Star (Amount: 1)

PostPosted: Sat Nov 04, 2017 4:29 pm    Post subject: Reply with quote

Yep! Part of the pattern Smile

How about:

e. Poncho features a hood that can cover the helmet when worn. It is closed at the neck with oval-shaped frame around the face. When worn down, hood should blouse under oval piece. Hood should hang down to shoulder-blade/mid back level in back and should have 2-4 inches/5-10 cm of fabric in front.
_________________

Costumer of the Year - 2010
Current Build Threads: Meadow Gown: http://www.forum.rebellegion.com/forum/viewtopic.php?t=100662
Ceremonial Leia: http://www.forum.rebellegion.com/forum/viewtopic.php?p=986837#986837
Back to top
View user's profile Send private message Visit poster's website
Ritin Kornas ()
Active Legion Member


Joined: 09 Jun 2009
Posts: 612
Location: Switzerland
Medals: None

PostPosted: Sun Nov 05, 2017 2:50 pm    Post subject: Reply with quote

Leia wrote:
Yep! Part of the pattern Smile

How about:

e. Poncho features a hood that can cover the helmet when worn. It is closed at the neck with oval-shaped frame around the face. When worn down, hood should blouse under oval piece. Hood should hang down to shoulder-blade/mid back level in back and should have 2-4 inches/5-10 cm of fabric in front.


Maybe it's good for native english speakers. But I can't tell as I don't understand the meaning of this part "hood should blouse under oval piece." :s
Well, of course I think I know what you want to mean, but that's because we had the discussion. For people who discover the standard, and are not native speakers, could be really annoying to understand.

I have no clue what "to blouse" means, and all translation I can find in dictionaries are... totally irrelevant to sewing/cosplay ^^ Could you please rephrase this?

Also, 2 little points :
- What do you mean by oval piece ? which piece do you refer to ?
- To be clearer, I think the "It" form your change should be "The hood" Wink


As an update regarding the hard shell of the helmet, I now have irrefutable proof it's not indents but just paint. With this pic I saw in the book "Costumes". Although this one have 9 stripes instead of the 8 of Leia. I think both should be allowed anyway, as it could be that the facts it is indented or not comes from the facts 2 types of helmets were produced: Hard "Hero" ones, and soft/rubber "stunt" ones. And it is proven that for stormtrooper armors hero/stunt have differences, so could be the case here too.
https://scontent-frx5-1.xx.fbcdn.net/v/t35.0-12/23224724_10155766277048290_1667720846_o.jpg?oh=aab959a9b746e75d0c20ae3181996a96&oe=5A00FB47
_________________
CO Rebel Legion Helvetica Base (serving Switzerland)
Member of the RL Galactic Senate Council
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   This topic is locked: you cannot edit posts or make replies.    Rebel Legion Forum Index -> Costume and Prop Making -> Royalty/Senatorial -> RLGS Archive All times are GMT
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can post calendar events in this forum
The Rebel Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred volunteer Rebel costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © 2019 Lucasfilm Ltd. & ™ All rights reserved. Used under authorization.


Powered by phpBB © 2001, 2005 phpBB Group